Техническое обслуживание гидравлической буровой установки: масло, фильтры и меры по предотвращению перегрева

Октябрь 16, 2026

Why Is Hydraulic Drilling Rig Maintenance Important?

Hydraulic drilling rig maintenance is essential for maintaining stable equipment operation and reducing avoidable downtime. The hydraulic system powers key drilling functions, including power head rotation, feeding, lifting, and other machine movements. Problems with hydraulic oil, filters, hoses, or cooling can affect drilling performance and increase the risk of component damage.

During mineral exploration and geological drilling, equipment may operate for extended periods in dusty environments and under demanding working conditions. Regular hydraulic system inspections help operators identify oil contamination, leakage, restricted filters, and abnormal temperature changes before they develop into more serious problems.

For operators using a hydraulic drilling rig, three areas deserve particular attention: hydraulic oil condition, filter maintenance, and overheating prevention.

1. Hydraulic Oil Maintenance for Drilling Rigs

Hydraulic oil transmits power through the system and helps lubricate internal components. Maintaining the correct oil level and condition is an important part of hydraulic drilling rig maintenance.

1.1 Check the Hydraulic Oil Level

Check the hydraulic oil tank before operation and confirm that the oil level remains within the specified range.

Insufficient hydraulic oil may affect system operation and contribute to abnormal temperature increases. If the level is too low, identify whether leakage or another problem is responsible before adding oil.

When topping up the tank, use the hydraulic oil grade specified for the machine. Do not mix different oil grades without confirmation from the manufacturer.

1.2 Inspect Hydraulic Oil Condition

Oil condition can provide useful information about the health of the hydraulic system.

During scheduled inspections, look for:

Darkened oil: May indicate oil deterioration or contamination.
Milky or emulsified oil: May indicate water contamination.
Visible particles: May indicate contamination or component wear.
Unusual temperature changes: May indicate a system problem that requires further investigation.

Visual inspection alone cannot identify every type of oil degradation. If the oil appears abnormal, take an appropriate sample and arrange further inspection.

Replace the oil when required by its condition or the equipment manufacturer’s maintenance schedule.

1.3 Use Clean Hydraulic Oil During Refilling

Contamination can enter the hydraulic system during oil storage, handling, or refilling.

To reduce this risk, use clean hydraulic oil and fill the tank through an appropriate filtration method. Keep filling equipment clean and prevent dust, water, and other contaminants from entering the reservoir.

For hydraulic systems, clean oil is not simply a consumable requirement. It is part of protecting pumps, valves, cylinders, and other hydraulic components.

2. Hydraulic Filter Maintenance and Replacement

Hydraulic filters help remove contaminants from the oil as it circulates through the system. If a filter becomes restricted or damaged, it may affect oil flow and system performance.

2.1 Inspect the Hydraulic Filters Regularly

During routine maintenance, inspect accessible filter housings and check for signs of leakage, damage, or abnormal operating conditions.

Pay attention to the following filter types where fitted:

Hydraulic return filter
Hydraulic suction filter
Pilot filter

Different filters serve different functions. Follow the drilling rig’s hydraulic system specifications to identify their locations and correct service procedures.

2.2 When Should Hydraulic Filters Be Replaced?

Filter service intervals depend on the machine design, operating hours, working conditions, and manufacturer recommendations.

The maintenance reference used for this article provides the following example schedule:

Maintenance Interval	Hydraulic Maintenance Task
Weekly, approximately 50 operating hours	Inspect the hydraulic return filter and clean or replace it as required
Monthly, approximately 200–250 operating hours	Replace the return filter element and inspect and service the pilot filter as specified
Every 500 operating hours	Clean the hydraulic oil tank and replace the hydraulic oil, suction filter, return filter, and pilot filter

These intervals are provided as a maintenance reference, not universal service intervals for every hydraulic drilling rig. Always confirm the correct schedule for the equipment being used.

Important: Cleaning a filter is not always an adequate substitute for replacement. Replace filter elements according to the manufacturer’s requirements, and never continue operating with a damaged or unsuitable filter.

2.3 Why Filter Maintenance Matters

Neglecting filter maintenance can allow contamination to accumulate or restrict the flow of oil through the system. Depending on the hydraulic circuit, this may contribute to unstable operation, increased wear, or overheating.

A consistent maintenance record helps operators track filter service dates and avoid missing scheduled replacements.

3. How to Prevent Hydraulic Drilling Rig Overheating

Hydraulic overheating can reduce operating efficiency and accelerate oil deterioration. If a drilling rig repeatedly operates at an abnormal temperature, the underlying cause should be identified rather than relying on cooling alone.

3.1 Understand the Recommended Oil Temperature

The maintenance reference used for this article recommends a hydraulic oil operating temperature range of 40–60°C and specifies that the machine should be stopped and allowed to cool when the temperature exceeds 65°C.

These values are equipment-specific reference figures, not universal limits for all hydraulic drilling rigs. Always follow the operating temperature range and shutdown requirements in the relevant manufacturer’s manual.

Do not continue prolonged operation when the hydraulic oil temperature exceeds the permitted range.

3.2 Check the Hydraulic Oil Level

A low oil level can contribute to abnormal operating conditions and may be associated with overheating.

Check the reservoir level and inspect the system for leakage. If oil loss continues, identify and repair the cause rather than repeatedly topping up the tank.

3.3 Inspect the Cooling System

Dust and debris can accumulate on hydraulic oil coolers and other heat-dissipation surfaces, reducing cooling effectiveness.

Inspect the cooling system for blocked surfaces and clean them according to the manufacturer’s instructions. Make sure the cooling components are operating correctly before returning the machine to service.

3.4 Check Filters and Hydraulic Components

Restricted filters, abnormal valve operation, or other hydraulic faults may contribute to excessive heat.

If overheating continues after checking the oil level and cooling system, inspect the filters and hydraulic components. Qualified technicians may need to check system pressure and valve operation to identify the underlying cause.

Do not adjust pressure settings or dismantle pressurized hydraulic components without the appropriate procedures and technical expertise.

4. Hydraulic Hose Inspection: Identify Problems Early

Hydraulic hoses operate under pressure and may deteriorate through aging, abrasion, vibration, or exposure to harsh working conditions.

During routine hydraulic drilling rig maintenance, inspect hoses and connections for:

Oil leakage around fittings
Cracks or visible aging on the hose surface
Bulges, deformation, or abrasion
Loose or damaged connections
Signs of contact with moving or hot components

Replace hoses that show serious damage or deterioration. Do not wait for a hose to burst before taking action.

Safety reminder: Shut down the machine, isolate the power source, release hydraulic pressure according to the manufacturer’s procedure, and allow hot components to cool before performing maintenance. Never use your hands to search for a pressurized hydraulic leak.

5. A Practical Hydraulic Drilling Rig Maintenance Checklist

The following checklist can help operators organize inspections and maintenance records.

Inspection Item	Что нужно проверить	Recommended Action
Hydraulic oil level	Oil level within the specified range	Top up with the correct oil after checking for leakage
Hydraulic oil condition	Darkening, emulsification, or visible contamination	Investigate and replace oil when required
Hydraulic filters	Condition, leakage, and scheduled service	Clean or replace according to the manual
Hydraulic hoses	Cracks, bulges, abrasion, and leaks	Replace damaged hoses
Cooling system	Dust buildup and cooling performance	Clean and inspect as specified
Oil temperature	Temperature within the permitted range	Stop and investigate if limits are exceeded
Maintenance records	Operating hours and completed work	Record inspections, replacements, and abnormal findings

The checklist should be adapted to the drilling rig model and working environment. In particularly dusty conditions or during intensive operation, more frequent inspections may be necessary.

6. When Should You Seek Professional Hydraulic System Inspection?

Routine maintenance helps prevent many avoidable problems, but some symptoms require further diagnosis.

Arrange a professional inspection if the drilling rig experiences:

Repeated hydraulic oil overheating
Persistent oil leakage
Unstable power head or cylinder movement
Abnormal hydraulic pressure
Repeated filter blockage
Unusual hydraulic pump noise

These symptoms can have several causes. Avoid replacing parts based on a single symptom without confirming the underlying fault.

For complex hydraulic problems, follow the equipment manufacturer’s troubleshooting procedures or consult qualified service personnel.

Заключение

Effective hydraulic drilling rig maintenance depends on clean hydraulic oil, timely filter replacement, regular hose inspections, and early action when operating temperatures become abnormal.

The maintenance reference used for this article gives an example hydraulic oil operating range of 40–60°C, with shutdown and cooling required when the temperature exceeds 65°C. Filter and oil replacement intervals should likewise be confirmed against the maintenance requirements for the specific equipment.

By maintaining accurate service records and responding promptly to abnormal conditions, operators can help protect hydraulic components and reduce avoidable downtime.

If you are planning a geological exploration project, explore the RUIXIN Core Drilling Rig range to learn more about drilling equipment for core sampling and mineral exploration.

Coming Next: Drilling Rig Winch and Wire Rope Maintenance: Inspection, Lubrication, and Safety Checks

Автор: Оборудование RUIXIN

Технический обзор: Инженерная команда RUIXIN